h3c路由器端口映射方法
你知道華為路由器怎么設置嗎?路由器的端口映射的方法有哪些?本文介紹了華為3com路由器的端口映射的方法，并且給出了詳細的操作步驟和命令語句，相信看完此文會對具體配置有詳細的了解。
************************************************** ******************************
* Copyright(c) 2004-2006 Hangzhou Huawei-3Com Tech. Co., Ltd. *
* Without the owner''''s prior written consent, *
* no decompiling or reverse-engineering shall be allowed. *
************************************************** ******************************
Login authentication
Username:admin
Password:
Ethernet1/0 current state :UP
Line protocol current state :UP
Description : Ethernet1/0 Interface
The Maximum Transmit Unit is 1500, Hold timer is 10(sec)
Internet Address is 218.206.191.49 <---(找到公網地址的端口)
IP Sending Frames'''' Format is PKTFMT_ETHNT_2, Hardware address is 000f-e24b-90c1
Media type is twisted pair, loopback not set, promiscuous mode not set
100Mb/s, Full-duplex, link type is autonegotiation
Output flow-control is disabled, input flow-control is disabled
Output queue : (Urgent queuing : Size/Length/Discards) 0/50/0
Output queue : (Protocol queuing : Size/Length/Discards) 0/500/0
Output queue : (FIFO queuing : Size/Length/Discards) 0/75/0
Last clearing of counters: Never
Last 300 seconds input rate 76409.96 bytes/sec, 611279 bits/sec, 221.16 packets/sec
Last 300 seconds output rate 169645.62 bytes/sec, 1357165 bits/sec, 217.84 packets/sec
Input: 84913558 packets, 1899317081 bytes, 84913558 buffers
1556505 broadcasts, 124223 multicasts, 0 pauses
374 errors, 0 runts, 0 giants
0 crc, 0 align errors, 374 overruns
0 dribbles, 0 drops, 0 no buffers
Output:73691649 packets, 1323897889 bytes, 73691649 buffers
19084 broadcasts, 0 multicasts, 0 pauses
0 errors, 0 underruns, 0 collisions
0 deferred, 0 lost carriers
[H3C]int e1/0
[H3C]nat server protocol tcp global 218.206.191.49 www inside 192.168.1.96 www
[H3C]nat server protocol tcp global 218.206.191.49 22 inside 192.168.1.96 22
[H3C]nat server protocol udp global 218.206.191.49 snmp inside 192.168.1.96 snmp
[H3C]nat server protocol udp global 218.206.191.49 snmptrap inside 192.168.1.96 snmptrap <--(一看就大白tcp/udp是以及談，www是80,snmp以及snmptrap是161.162端口)
[H3C]dis thellos
interface Ethernet1/0
ip address 218.206.191.49 255.255.255.248
firewall packet-filter 3000 inbound
nat outbound 3001 <--(這是客戶上彀用的地址池不消管，其它的就是端口照射了)
nat server protocol tcp global 61.178.77.9 www inside 192.168.1.96 www
nat server protocol tcp global 61.178.77.9 22 inside 192.168.1.96 22
nat server protocol udp global 61.178.77.9 snmp inside 192.168.1.96 snmp
nat server protocol udp global 61.178.77.9 snmptrap inside 192.168.1.96 snmptrap
思科網絡的端口照射原理是同樣的號令紛歧樣罷了，這搭只給出配備布置。
思科網絡>en
思科網絡#config t
思科網絡(config)Ip nat inside source static tcp 192.168.1.96 80 218.206.191.49 80
思科網絡(config)Ip nat inside source static tcp 192.168.1.96 22 218.206.191.49 22
思科網絡(config)Ip nat inside source static tcp 192.168.1.96 161 218.206.191.49 161
思科網絡(config)Ip nat inside source static tcp 192.168.1.96 162 218.206.191.49 162
更多相關文章推薦：
10.思科與H3C配置命令對比
【h3c路由器端口映射方法】相關文章：
華為路由器端口映射方法08-30
h3c路由器配置07-31
H3C路由器配置命令07-19
h3c路由器默認密碼07-21
H3C路由器簡單配置05-14
H3C路由器的配置命令09-05
H3C路由器常用配置命令10-11
H3C路由器基本配置命令10-21
H3C路由器NAT配置實例10-08
H3C路由器tracert命令怎么開啟08-27